elastic resilience
英 [ɪˈlæstɪk rɪˈzɪliəns]
美 [ɪˈlæstɪk rɪˈzɪliəns]
弹性回弹；弹性能
双语例句
- Optimal powdering degree and elastic resilience were achieved when the content of whisker was3%.
当镁盐晶须含量为3%时，泡沫粉化程度和回弹性改善达到最优值； - The mechanical model of the whole structure is the story-shear model, the superstructure uses the elastic model, meantime the rubber base isolated system uses the bilinear resilience model.
结构计算模型考虑层间剪切变形，上部结构层间刚度采用线弹性模型，隔震层刚度采用双线性恢复力模型。 - A Preliminary Study of Elastic Resilience of Wood Surface by Stroboscope Method
频闪法对木材表面回弹性能的研究初报 - When the membrane stress is removed, circle elasticity deformation and radial shorten elastic deformation cause resilience.
当膜力卸除后，周向弹性变形和径向缩短的弹性变形导致回弹。 - When the content of the oligomer in the phenolic resin was 3%, the powdering of the modified foam was only 40% of that of non-modified foam, with elastic resilience higher than 60%;
当预聚物的质量分数为3%时，改性泡沫的粉化程度仅为未改性的40%，且使泡沫具有一定的弹性，回弹率大于60%； - The results showed that in case of adding PP, the tensile strength, melt flow rate and compression set of the SEBS increase, but the elongation at break decreases quickly and the elastic resilience decreases gradually;
研究结果表明：加入PP时，材料的拉伸强度、熔体流动速率和压缩永久变形增大，但其断裂伸长率迅速下降，回弹性逐渐降低； - An attempt to explore the technique of graft copolymerization of silk fabrics in order to raise the elastic resilience of silk fabrics while preserving their style and performance.
本文着眼于在力求保持真丝织物风格及其特性的同时，探索提高其弹性回复的接枝率范围的合适的接聚方法。 - Different pretreatment process can differently affect fabric style such as drawing linearity, elastic resilience, bending rigidity, shearing characteristic, compression work, surface roughness, bulkiness etc.
而不同的前处理加工对织物风格如拉伸线性度、回弹性、弯曲刚度、剪切特性、压缩功、表面粗糙度、膨松性等影响各异。 - The effect of heat setting conditions on the elastic resilience of IPP fibers has been investigated. The elastic resilience compares with other mechanical properties.
作者研究了热定型条件对丙纶弹性回复率的影响，并将回弹率与纤维的其它力学性质作了对比。 - Elastic resilience of wood surface is studied by stroboscope method.
采用频闪法对木材表面回弹性能进行了研究，结果表明：木材表面的回弹性能与碰撞球体的选择有关； - The article describes calculation method of bending moment and elastic resilience value Δα, and analyzes all kinds of effect factors.
叙述了弯曲力矩及弹性回弹量Δα的计算，全面分析了影响弯曲件弹性回弹的主要因素； - The higher the PTT percentage, the elastic resilience is better.
PTT含量增加，则纱线的弹性提高。 - Bending Elastic Resilience and Its Controlling Technology
弯曲弹性回弹及其工艺技术控制方法 - Generally, the elastic resilience became better with the annealing temperature rising except an abnormity at 3 at% Zr. It was related to the Ms temperature of alloys which was slightly lower than the room temperature.
一般情况下，随着退火温度的升高，该系列合金的弹性回复能力越好。但Zr元素含量为3at%时出现异常，与此成分合金的Ms点略低于室温有关。